Sails sets: Mainsail + Headsail (calculation)

Calculation template

Do you want to read more articles like this?

How does it work?

Following the ORC VPP methodology, this template calculation combines the individual sail’s characteristics of a user-defined mainsail and a user-defined headsail to produce a set of coefficients that describe the aerodynamic behavior of the entire sails set. The template covers both jib and genoa headsail types.

mainsail is a sail with the luff attached to the mainmast. The mainmast is the only mast in a una rigsloop rig, or cutter rig, or the fore mast in a ketch rig or yawl rig, or the aft mast in a schooner rig.

A headsail is a sail set forward of the mast, or of the foremast mast if there is more than one mast, where the measurement between the half luff point and the half leech point, known as mid width, is less than 75% of the foot length (if mid width length ≥ 75% of the foot length, the sail is considered a spinnaker).

The template first calculates the lift and the zero-lift parasite drag coefficients and the height of the aerodynamic center of effort of the complete sails set. It also determines the value of the quadratic parasite drag, which is the additional parasite drag generated by the lift.

Then, it calculates the effective height and an efficiency coefficient, both necessary for the computation of the induced drag (drag due to lift) and the total drag coefficient of the sails set.

Finally, the lift and drag aerodynamic coefficients are resolved into two orthogonal forces: the driving force coefficient, thrust, and the heeling force coefficient, side.

Both the Chart and the Table display the following results calculated for AWA (apparent wind angles) from 0 to 180 degrees:

ThrustDriving Force Coefficients.
SideHeeling Force Coefficients.
LiftLift Coefficients.
Drag TotalDrag Total = Zero-lift Parasite Drag + Induced Drag.
The Induced Drag component also includes the effect of the variation of Parasite Drag with lift (Quadratic Parasite Drag).
DragDrag = Zero-lift Parasite Drag = Friction Drag + Pressure Drag.
Parasite Drag is also known as Viscous Drag. Pressure Drag is also known as Form Drag.
Eff. spanEffective Height / Reference Height.
CEHeight of the Aerodynamic Center of Effort / Reference Height.
Headsail
Sails sets: Mainsail + Headsail chart results
Sails sets: Mainsail + Headsail. “Example” yacht results.

The aerodynamic model used in this calculation does not include the windage which is the force generated by the apparent wind on the above-water part of the hull, superstructures, the mast, the rigging wire, and the crew.

References:

Send us a Message

    Related Articles

    Points of sail

    The points of sail refer to the course a boat is sailing in relation to the wind. They are defined in reference to the wind angle, which is the angle between the course sailed and the direction of the wind. The following terms are used: close-hauled, close reach, beam reach, broad reach, run, dead-run.

    International Measurement System: Sails

    The International Measurement System (IMS) is a set of rules that define what and how is measured on a boat. It is used by the Offshore Racing Congress (ORC) as a measurement platform on its ORC Rating Systems (ORC International and ORC Club). In this article, we deep dive into sails from the IMS perspective.

    Responses

    1. Nice! This is the first time I see combined coefficients of the ORC-system published! May I suggest that you add a boat name/description field, that shows on the graph as well, so one can save screen dumps of various rigs/boats.

      1. Hi Mikko,
        Following your suggestion, we have added a new tab called” Design” to the Sails Sets calculation templates. This new tab contains two fields: “Name” and “Description.” Once the calculation is run, both the Chart and the Table results will automatically display at the top the “Chart Title”, the “Name”, and the “Description.” We hope that helps! Thanks for being an active Navalapp supporter!